78-3 Update February 2106

Its been awhile since my last update on the 78 series. Last October, the owners of hulls 1, 2 and 3 were all in New Zealand to review progress on our individual boats and have a good look at 78-1 which was furthest along. 78-1 owned by Steve and Linda Dashew, the designers of the FPB series is now nearing completion and is tentatively christened “Cochise”. Headed for launch and builder’s trials in March, she will then head to Owner’s trials shortly after.

Tentatively, all three 78 owners, Steve Dashew, Peter Watson (FPB 64 Grey Wolf and 78-2) and yours truly will be back in New Zealand in June 2016 for Owner’s Training on “Cochise” as well as review of progress on our individual boats. Note that Steve Dashew, in ways only his devious mind can devise, has chosen winter in the Southern Hemisphere with all the nastiness the Southern Ocean can drum up for his playground. He was in his glory when we conducted the first open house with launch of the FPB64 when the Southern Ocean dished up a strong on shore gale for the ocassion. At least he didn’t turn off the stabilizers beam to during the open house like he did on our trip from the Bay of Islands back to Whangarei on my newly launched “Iron Lady” – just to “see how she would behave”. At the time, Deb had three large pots of herbs on top of the locker over the range top – they didn’t think much of his experiment and the result was flying pots, plants and dirt everywhere. I will see if I can return the favor on Cochise during Owner’s Training.

Anyway, back to 78-3 and the latest batch of photos form Circa. First, a shot from below decks showing the spill wall around the mechanical room and a manometer set up to pressure test one of the tanks.

Ali Fab  405

The next picture is looking at one of the cofferdams which encloses the stabilizer mechanisms. You can just see the massive mounting plate and reinforcing around it.

Ali Fab  406

The next shot shows some of the looms thru the structural framing which will carry the myriad of plumbing and electrical services thru the boat.

Ali Fab  407

We also chose to put 4 port lights on the boat – one in each guest stateroom, one in my office across from the master stateroom and one in the master stateroom. Circa has a full foundry and the made the molds, poured and finished machined the frames. They are a work of art and VERY heavy duty.

Ali Fab  411

The following view is form the companionway leading forward to the forepeak. The forepeak will be home for the full size washer and dryer as well as an exercise area and lots of storage.

Ali Fab  414

Headed to the back dci for a moment, this locker on port side under the matrix deck overhand houses the refrigeration compressors which are both water and air cooled as well as a day head. Looking forward, you can see into the great room where the galley will be on the left with seating and lower helm station forward.

Ali Fab  417

Work has begun on the shaft logs and the rudder as well. Yo9u can get a sense of how massive things are by looking at the fellow working there. Those stern tubes are designed to house the shafts which are 2.5 inches in diameter.

Ali Fab  419

This shot shows one of the two rudders under construction.

Ali Fab  427

And the final metalwork picture is of the forward mast under construction.

Ali Fab  426

Turning to the Chippies (Kiwi for carpenters), the following shots show the interior cabinetry under construction. We chose a pickled Australian Oak, Rift Cut for uniform grain structure for our interior. The finish will be natural satin varnish.

The first shows the cabinet that goes across the aft end of the galley. The oven has even temporarily installed to check the fit.

Interior  65

The next three shots show the forward galley area which is “U” shaped. You can also see the counter top garages for storage.

Interior  68

Interior  69

Interior  76

This picture shows one of the refrigeration boxes. The galley has a large upright refrigerator and two large freezers along the port side of the galley.

Interior  84

Shown below is the fiberglass enclosure for the master “shun” (combination shower and tub).

Interior  88

A long way to go but I hope you can get a sense of just how ridiculously strong the 78 is along with the craftsmanship of the good folks at Circa.

Til next time.

This entry was posted in 78-3 Updates. Bookmark the permalink.

7 Responses to 78-3 Update February 2106

Leave a Reply to David Cretney Cancel reply